Remote-processing RPC-220 Uživatelský manuál Strana 45

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 47
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 44
TECHNICAL SPECIFICATIONS SECTION 15
Page 15-1
TECHNICAL SPECIFICATIONS SECTION 15
CPU
Phillips 80C552 operating at 22.1184 Mhz
Power Supply
Inputs: 5 ±0.25VDC or
6-16V (RPC-220 P/N 1715, 1720) or
5.4 to 21V (RPC-220 P/ N 1710)
Higher input voltage possible with heat sink.
Current: 180 ma (P/N 1715, 1720) maximum.
100 ma (P/N 1710) maximum.
Outputs not loaded.
5 ma maximum, lowest power mode (P/N
1710)
Currents measured without RS-232 attached.
Screw terminals provided for + 5V and external
high voltage input.
Memory
External RAM -
128K or 512K, depending upon model. 32K
accessible as code during development mode.
Code address during development m ode is 0x8000 to
0xffff. All external RAM accessed using MOVX
type commands and by segment selecting.
RAM is battery backed up when real time clock
option is installed. Backup time varies with usage
and operating temperature. Backup time is estimated
at 4 to 6 years at 25°C, board not powered. Backup
time reduced by 50% when operating at 50°C.
Program EPROM -
32K, Atmel type 29C256. This is a PEROM and
does not need sector er ase. Howe ver, data is
written in 64 byte blocks.
Monitor included. This is written over after program
development.
A 64K UV EPROM (27C512 type) is possible. See
SECTION 3, PROG RAM S LARGER TH AN 32K
for modification instructions.
Analog Input
Channels: 8
Resolution: 10 bits (about 5 m v/count)
Range: 0 - 5V
Input impedance: 100K ohms
Conversion time: 28 m icro-seconds
Reference: Adjustable fr om about 4.8 to 5.2 volts
Analog Output
Channels: 2
Resolution: Effectively 8 bits (20 mv)
Range: 0 - 5V Maximum output voltage, and
accuracy, dependent upon 5V supply
Ripple: 20 mv P -P ma ximum at 50% duty
cycle, 4. 8 Khz PWM frequency
Output cur rent: 2 ma m aximum /chan nel, 4 ma total.
Response time: 300 milli-seconds or less
Analog outputs use PWM outputs. When an analog
output is used, its corresponding PWM output cannot be
used.
PWM O utput
Channels: 2
Duty cycle: 0 to 100% 256 steps
Frequency: programmable from about 163 to 42 Khz.
Output cur rent: 4 ma m aximum , T TL co mpatible
PWM outputs generate analog outputs. When analog
output is used, its corr esponding P WM output cannot
be used.
Real Time Clock
Type: DS1689
Accuracy: 1 min/month. This will vary
depending upon operating temperature.
Ac cura cy spe cif ied at 2 5°C
Interrupts: May g enerate an INT 1 when J3-23 is
jumpered to J3-25. Also used to wake
up card from low power mode.
Battery backup: Battery backs up RAM. Connector for
external battery provided when special
ordered without battery.
Operating life: Four to 6 years, depending upon
temperature and humidity.
Reset
CPU resets when 5V supply falls below about 4. 65 volts.
Held in reset until supply rises to about 4.65 volts. Reset
time is about 300 ms. A pulse from the real time clock
resets CPU to wake it up from low power mode.
LCD Display Port
Zobrazit stránku 44
1 2 ... 40 41 42 43 44 45 46 47

Komentáře k této Příručce

Žádné komentáře